No. de modelo: 7075 Aplicación: Decoraciones, Disipador de calor, Herramientas de transporte, Puerta y ventana, Pared de vidrio, Tanque Grado: Serie 7000 Técnica: Laminado en caliente Temple: T3 - T8 Superficie: Acabado de molino Especificación: Estándar de China Código HS: 7606129000 Tipo: Hoja de aluminio Forma: Superficie plana Tratamiento: Acabado de molino Aleación: Aleación Certificación: ASTM, JIS, GB / T, EN, ASTMB Marca registrada: HM Origen: China 7075 T6 Acabado de molino Hoja de aleación de aluminio llano \ n \ nAleación: 1050, 1060, 1100 , 3003, 5052 5083 6061 5005 6063 6082 7075 etc. \ nTemperamento: H12. H14. H16. H18. H112. H22. H24. H26. H32. H34. H36. H38. O, etc. \ nEspesor: 0,2 mm - 400 mm \ nAncho: Menos de 2800 mm \ nLongitud: Menos de 10000 mm \ nEmbalaje: Estándar de exportación, cubriendo con papel marrón y película de plástico y luego empacado con banda de acero y caja / paleta de madera \ nOrigen: China \ nLlead Tiempo: Dentro de 25 días \ nProductividad: 4000MT / Mes \ nPago: T / T, L / C irrevocable a la vista \ nObservaciones: Los requisitos específicos de aleación, temple o especificación se pueden discutir según su solicitud.
| Aluminium Plate / Slab 5052 |
| Typical Chemistry (% Maximum unless shown as a range) |
\ n \ n \ n
| Cu | Si + Fe | Mn | Mg | Zn | Cr | Al |
| 0.10 | 0.45 | 0.10 | 2.2 / 2.8 | 0.10 | 0.15 / 0.35 | Balance |
\ n \ n \ n
| Characteristics |
| 5052 is one of the higher strength non-heat-treatable alloys. It has a high fatigue strength and is a good choice for structures subjected to excessive vibration. The alloy has excellent corrosion resistance, particularly in marine atmospheres. The formability of the grade is excellent and in the annealed condition it offers higher strengths than 1100 or 3003 grades. |
| Typical Applications |
| 5052 is often used in high strength sheet metal work, marine components, appliances, fuel and oil tubing. |
| Mechanical Properties |
\ n \ n \ n
| Tensile Strength | Yield Strength | Elongation | Brinell Hardness |
| ksi | MPa | ksi | MPa | % in 2"
(50mm) |
|
| 5052-0 | 28.0 | 196 | 13.0 | 91 | 25 | 47 |
| 5052-H32 | 33.0 | 231 | 28.0 | 196 | 12 | 60 |
| 5052-H34 | 38.0 | 266 | 31.0 | 217 | 10 | 68 |
\ n \ n \ n \ n
| Aluminium Plate / Slab 5083 |
| Typical Chemistry (% Maximum unless shown as a range) |
\ n \ n \ n
| Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Al |
| 0.10 | 0.40 | 0.40 | 0.3 / 1.0 | 4.0 / 4.9 | 0.25 | 0.05 / 0.25 | 0.15 | Balance |
\ n \ n \ n
| Characteristics |
| 5083 is the highest strength non-heat-treatable alloy in commercial use. It has good formability and weldability and retains excellent tensile strength in the weld zone by virtue of its as-rolled properties. It is used most often in structures requiring high weld efficiency and maximum weld strength. 5083 also has excellent resistance to corrosion. |
| Typical Applications |
| 5083 is commonly used in highly stressed welded assemblies, dump truck boxes, storage tanks, and cryogenic vessels. |
| Mechanical Properties |
\ n \ n \ n
| Tensile Strength | Yield Strength | Elongation | Brinell Hardness |
| ksi | MPa | ksi | MPa | % in 2"
(50mm) |
|
| 5083-0 | 42 | 294 | 21 | 147 | 22 | - |
| 5083-H321 | 46 | 322 | 33 | 231 | 16 | - |
\ n \ n \ n \ n
| Aluminium Plate / Slab 6061 |
| Typical Chemistry (% Maximum unless shown as a range) |
\ n \ n \ n
| Cu | Si | Fe | Mn | Mg | Zn | Cr | Ti | Al |
| 0.15 / 0.40 | 0.4 / 0.8 | 0.70 | 0.15 | 0.80 / 1.2 | 0.25 | 0.04 / 0.35 | 0.15 | Balance |
\ n \ n \ n
| Characteristics |
| 6061 is a heat-treatable grade widely used in light to medium strength structural applications. The alloy has good corrosion resistance and weldability and possesses good formability in the 0 to T4 tempers. 6061 does lose appreciable strength when welded and it is replaced by the 5000 series alloys where afterweld strength is a prime consideration. |
| Typical Applications |
| 6061 is used in structural areas where both strength and corrosion resistance is required, truck bodies and frames, and towers. |
| Mechanical Properties |
\ n \ n \ n
| Tensile Strength | Yield Strength | Elongation | Brinell Hardness |
| ksi | MPa | ksi | MPa | % in 2"
(50mm) |
|
| 6061-0 | 18.0 | 126 | 8.0 | 56 | 25 | 30 |
| 6061-T4 | 34.0 | 238 | 22.0 | 154 | 21 | 65 |
| 6061-T6 (T651) | 44.0 | 308 | 41.0 | 287 | 17 | 95 |
\ nTambién podemos hacer tamaños de corte más pequeños según los requisitos del cliente. \ n \ n
Grupos de Producto : Lámina y placa de aluminio
